DIY Tub Setup.
DIY Tub Setup.
Blog Article
What are your thoughts and feelings about Tools You Need to Install a New Bathtub ?
Installing a tub isn't specifically rocket science, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is readily accessible, the job can relocate quickly; if you have to open a wall to eliminate the old tub as well as place the brand-new tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have qualified yourself for the work as well as are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This short article will certainly assist you install a new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous supply of water pipes.
Your devices as well as product list ought to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome due to the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the faucet and also the sink. Secure the tap in place with the supplier given backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub must wait up until the bathtub has been used at the very least when as this will certainly settle it into its last placement.
Planning for the Setup
First of all, the supporting structure provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealer can fracture fairly early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that review on How to Install a Bathtub Yourself when doing a search on the web. Sharing is caring. Helping people is fun. Thank you for taking the time to read it.
Start Now Report this page